A web-based 3D ontology navigation system for spinal disease diagnosis

The Journal of Supercomputing - This paper presents a web-based three-dimensional (3D) navigation system for a spinal disease ontology using a 3D virtual human spine. The 3D navigation system...     

Development of microbially influenced corrosion on carbon steel in a simulated water injection system

Microbially influenced corrosion (MIC) on internal pipeline surfaces has become a severe problem during the water injection process in secondary oil recovery. The formation of a biofilm, normally dominated by sulfate‐reducing bacteria (SRB), is believed to be the critical step of the MIC process. A continuously fed biofilm simulating the water injection process was operated to investigate the influence of biofilm development on MIC behavior in the early phase of corrosion development. The development of the corrosion product film and biofilm was monitored for 5 months with electrochemical impedance spectroscopy, linear polarization resistance, scanning electron microscopy, 3D optical profiling, and direct weight measurement. MIC development was found to comprise three phases: initialization, transition, and stabilization. The initialization phase involved the formation of the corrosion product layer and the initial attachment of the sessile microbes on metal surface. In the transition phase, the MIC process gradually shifted from charge‐transfer‐controlled reaction to diffusion‐controlled reaction. The stabilization phase featured mature and compact biofilm on the metal surface, and the general corrosion rate (CR) decreased due to the diffusional effect, while the pitting CR was enhanced at a lower carbon source level, which supported the mechanism of direct electron uptake from the metal surface by SRB.     

STL模型特征信息的自适应分层的研究

模型的分层是3D打印前处理的一个重要环节，针对目前分层算法效率低、不能有效保留模型细微特征的问题，提出了一种新的基于STL模型特征信息的思想。首先提取模型的特征边，对特征边内实体表面采用区域增长算法进行表面分割，然后对分割后的表面判断其类型，最后对于不同的表面类型采用不同的分层求交处理算法。利用VC++6.0平台和OpenGL显示技术，依据模型表面几何特征自适应地变动层厚，减小台阶效应，加快分层效率，同样能很好地保留模型局部特征，且该算法可以根据实际模型的成型方向，实现分层方向的改变，保证成型零件的精度。     

基于微型塌落筒和稠度漏斗的膏体充填料浆流变参数预测研究

充填料浆流变参数的准确测定是合理评价其管道输送特性的关键，目前充填料浆流变参数主要采用流变仪测试，工程适用性较差。基于圆锥塌落筒模型和圆柱塌落筒模型，结合流变仪测试，对比分析了不同形状尺寸塌落筒测试屈服应力的准确性，确定了微型塌落筒最佳形状尺寸为柱形 100 mm×100 mm；在此基础上构建了屈服应力-塌落度关系模型，经验证在无量纲屈服应力范围为 0~0.1 时该模型可以准确计算料浆屈服应力；通过自制稠度漏斗测试充填料浆流出时间，探索流变仪测试塑性粘度与流出时间关系，结果表明相同质量浓度时，料浆流出时间与其塑性粘度呈负相关关系，料浆质量浓度变化时其流出时间与塑性粘度关系不明显。     

黔北桑木场背斜铅锌矿深部找矿实例分析*#br#

黔北桑木场背斜位于上扬子地块黔北隆起区毕节弧形褶皱带与赤水克拉通盆地的交汇部位，属于有利的铅锌成矿区带。区内铅锌矿的赋矿层位主要有震旦系灯影组、寒武系清虚洞组、高台组及石冷水组，矿体多产于背斜核部并受断层或裂隙控制。通过对地层岩性特征、地表矿化特征、控容矿构造特征、化探异常特征、物探异常特征等进行综合研究，选择在成矿有利地段进行了工程验证，为进一步开展桑木场背斜铅锌矿深部找矿工作提供了思路。     

Experimental study on filling imbalance of plastic parts with microcylinders

To examine the microscale filling imbalance in the present work, an eight-cavity injecting mold with microcylindrical-hole arrays fabricated by micro-electrical discharge machining milling technology was developed. Polypropylene (PP) was used to carry out single factor filling flow experiments with vacuuming the mold cavities. The filling height difference of micro cylindrical hole at the same position between cavity I and cavity II, which was the index of filling imbalance and the effect of mold temperature and injection rate on the filling imbalance of microholes with diameters of 200 μm and 300 μm was investigated. The results revealed that the maximum height difference reached 101 μm with low process parameters, and the filling imbalance was obvious. With the increase in mold temperature and injection rate, the filling imbalance was weakened. In addition, the impact of the scale effect on filling imbalance was checked. The filling imbalance of micro holes in 200 μm was greater than that in 300 μm using identical process parameters. With the increase in mold temperature and injection rate, the filling height difference of the two kinds of micro holes decreased. POLYM. ENG. SCI., 60:22–31, 2020. © 2019 Society of Plastics Engineers     

水泥乳化沥青砂浆峰值应变的试验研究

采用万能材料试验机对不同配合比的水泥乳化沥青砂浆(CA砂浆)进行了单轴压缩试验,研究了结构组成对CA砂浆峰值应变的影响,并进一步建立了峰值应变与抗压强度的定量关系.结果表明,峰值应变随A/C、W/C的减小而减小,A/C的变化改变了CA砂浆的结构特性,W/C的不同则影响了内部能量的释放过程.CA砂浆的峰值应变与抗压强度的平方根成正比,且符合林大炎方程,结合峰值应变的理论计算及CA砂浆充填层的实际受力状态,估算了充填层发生伤损破坏时的几何尺寸变化.     

电磁场作用下球形磁极辅助研磨弯管内表面研究

弯管弯曲成形后,在弯折处易产生微裂纹、褶皱等表面质量缺陷问题。本文通过采用六自由度机械手拖动电磁场发生装置沿加工轨迹往复运动,电磁场发生装置驱动球形辅助磁极绕管件内壁转动,实现了对弯管内表面的光整加工。在此基础上,通过对弯管轮廓采集及曲线拟合,重新构建了弯管中心线并转换为新的研磨加工轨迹。采用超景深3D电子显微镜和触针式表面粗糙度测量仪对研磨试验前后弯管内表面的形貌和粗糙度进行了对比分析。结果表明,通过重新构建研磨加工轨迹,试验装置有效解决了研磨弯折处的干涉与研磨不均匀等问题。研磨55 min后,表面粗糙度由原始的0.713μm降低到0.194μm,铜合金弯管内表面原始质量缺陷基本去除,表面纹理较为致密均匀。该方法有效避免了未规划研磨轨迹时出现的犁耕等纹理缺陷,提高了弯管的服役可靠性。     

Ultrafine porous boron nitride nanofiber-toughened WC composites

Porous fibers are widely used in catalysis chemistry and hydrogen storage but are rarely used in structural ceramics. In this study, spark plasma sintering was used to prepare an ultrafine porous boron nitride nanofiber-toughened WC composite for the first time. The obtained WC-0.05 wt% ultrafine porous boron nitride nanofiber composites exhibited better properties (ie, a 2.3% increase in hardness and a 19.6% increase in fracture toughness) compared to those of the pure WC specimen. The fiber porosity improved the second phase-WC matrix microstructural combination. The described approach is a novel preparation method for the WC composites. Furthermore, a new toughening mechanism, which is based on “pinning and stretching”, was determined. These findings suggest that porous boron nitride fibers can be considered to be second phases for toughening the WC composites.     

PVC地板行业研究现状及发展趋势

概述了国内外PVC地板行业的生产及应用现状,比较了几种地板材料的优缺点,介绍了PVC地板生产技术的研究进展情况,分析了国内PVC地板行业的发展趋势。